# chainer.optimizers.CorrectedMomentumSGD¶

class chainer.optimizers.CorrectedMomentumSGD(lr=0.01, momentum=0.9)[source]

Momentum SGD optimizer.

This implements momentum correction discussed in the third section of Accurate, Large Minibatch SGD: Training ImageNet in 1 Hour.

MomentumSGD implements the equation (10) of the paper. This optimizer implements the equation (9).

To get better understanding between the two methods, we show the equivalence between the equation (9) and modification of the equation (10) that takes momentum correction into account. First, we set $$v_{t} = \eta_{t} u_t$$. We substitute this relation to the equation (10).

$\begin{split}v_{t+1} &= m\frac{\eta_{t+1}}{\eta_{t}}v_t + \eta_{t+1}g_t \\ &= m\frac{\eta_{t+1}}{\eta_{t}}\eta_{t}u_t + \eta_{t+1}g_t \\ &= \eta_{t+1}(m u_t + g_t) \\\end{split}$

From this result, we derive $$u_{t+1} = m u_t + g_t$$, which is how update tensors are calculated by CorrectedMomentumSGD. Thus, the equivalence is shown.

Parameters
• lr (float) – Learning rate.

• momentum (float) – Exponential decay rate of the first order moment.

Methods

Registers a hook function.

Hook function is typically called right after the gradient computation, though the timing depends on the optimization method, and the timing attribute.

Parameters
• hook (callable) – Hook function. If hook.call_for_each_param is true, this hook function is called for each parameter by passing the update rule and the parameter. Otherwise, this hook function is called only once each iteration by passing the optimizer.

• name (str) – Name of the registration. If omitted, hook.name is used by default.

• timing (str) – Specifies when the hook is called. If ‘auto’, the timimg property of the hook will decide the timing. If ‘pre’, the hook will be called before any updates. If ‘post’, the hook will be called after any updates.

call_hook(hook)[source]
call_hooks(timing='pre')[source]

Invokes hook functions in registration order.

Checks if there is NaN in grads when dynamic loss scaling used.

create_update_rule()[source]

Creates a new update rule object.

This method creates an update rule object. It is called by setup() to set up an update rule of each parameter. Each implementation of the gradient method should override this method to provide the default update rule implementation.

Returns

Update rule object.

Return type

UpdateRule

is_safe_to_update()[source]
loss_scaling(interval=1000, scale=None)[source]

Configures the loss scaling algorithm.

Parameters
• interval (int) – Number of iterations until scaling factor gets doubled. This is effective when “dynamic” loss scaling is used.

• scale (float) – Loss scaling factor. If None, “dynamic” loss scaling is used, otherwise “static” loss scaling is used.

new_epoch(auto=False)[source]

Starts a new epoch.

This method increments the epoch count. Note that if the optimizer depends on the epoch count, then user should call this method appropriately at the beginning of each epoch.

Parameters

auto (bool) – Should be True if this method is called by an updater. In this case, use_auto_new_epoch should be set to True by the updater.

Reallocate gradients cleared by cleargrad().

This method allocates arrays for all gradients which have None. This method is called before and after every optimizer hook. If an inheriting optimizer does not require this allocation, the optimizer can override this method with a blank function.

remove_hook(name)[source]

Removes a hook function.

Parameters

name (str) – Registered name of the hook function to remove.

serialize(serializer)[source]

Serializes or deserializes the optimizer.

It only saves or loads the following things:

It does not saves nor loads the parameters of the target link. They should be separately saved or loaded.

Parameters

serializer (AbstractSerializer) – Serializer or deserializer object.

set_loss_scale(loss_scale)[source]

Sets loss scaling factor.

Sets a target link and initializes the optimizer states.

Given link is set to the target attribute. It also prepares the optimizer state dictionaries corresponding to all parameters in the link hierarchy. The existing states are discarded.

Parameters

Returns

The optimizer instance.

Note

As of v4.0.0, this function returns the optimizer instance itself so that you can instantiate and setup the optimizer in one line, e.g., optimizer = SomeOptimizer().setup(link).

update(lossfun=None, *args, **kwds)[source]

This method runs in two ways.

• If lossfun is given, then it is used as a loss function to compute gradients.

In both cases, the computed gradients are used to update parameters. The actual update routines are defined by the update rule of each parameter.

update_loss_scale()[source]

Enables or disables use of cleargrads() in update.

Parameters

use (bool) – If True, this function enables use of cleargrads. If False, disables use of cleargrads (zerograds is used).

Deprecated since version v2.0: Note that update() calls cleargrads() by default. cleargrads() is more efficient than zerograds(), so one does not have to call use_cleargrads(). This method remains for backward compatibility.

use_fp32_update(flag=True)[source]

Enables use of parameter update in fp32.

__eq__(value, /)

Return self==value.

__ne__(value, /)

Return self!=value.

__lt__(value, /)

Return self<value.

__le__(value, /)

Return self<=value.

__gt__(value, /)

Return self>value.

__ge__(value, /)

Return self>=value.

Attributes

epoch = 0
lr

Alias to self.hyperparam.lr

momentum

Alias to self.hyperparam.momentum

t = 0
target = None
use_auto_new_epoch = False